ACCESSORY FITTING INSTRUCTIONS

JAGUAR

I-PACE

BIKE CARRIER HARNESS

T4K11471 / T4K11423 / C2C8870 / T4K9902 / C2C26750 / C2P4787

FITTING INSTRUCTION

WARNING
  • Accessories which are not correctly installed can be dangerous. Read the instructions carefully prior to ordering and installation to make sure this accessory is applicable to your variant of vehicle. Comply with instructions at all times. If in doubt, contact your nearest approved retailer.
Kits Required Part Number
Bike Carrier Harness T4K11471
Trailer Module (TRM) T4K11423
TRM M6 Nut C2C8870
TRM Bracket (Only required if your vehicle is equipped with 'Coil Suspension') T4K9902
TRM Bracket M6 Nut (Only required if your vehicle is equipped with 'Coil Suspension') C2C26750
TRM Bracket Fixing (Only required if your vehicle is equipped with 'Coil Suspension') C2P4787

Warnings / Cautions / Notes

WARNING
  • The 21 model year specific electrics kits (T4K11471) and (T4K11423) must be used when installing the bike carrier harness to some of the 21 model year vehicles and all vehicles that are 22 model year onwards. Vehicles with Vehicle Identification Number (VIN) where the 10th character is the letter 'M' or a subsequent letter of the alphabet, must only have electrics kits (T4K11471) and (T4K11423) installed. Example: SADHA2B14M1F89112. VINs where the 10th character is the letter 'K' or 'L' must only have older electrics kit (T4K1472) installed. Example SADHA2A18K1F60131.
NOTE
  • TRM Bracket (T4K9902) requirement for 'Coil Suspension' vehicles only from VIN SADHA2A14N1622769 onwards

Bike Carrier Harness (Bill of Materials)

TRM

TRM M6 Nut

TRM Bracket

NOTE
  • This part is 'ONLY' required if your vehicle is equipped with 'Coil Suspension'.

TRM Bracket M6 Nut

NOTE
  • This part is 'ONLY' required if your vehicle is equipped with 'Coil Suspension'.

TRM Bracket Fixing

NOTE
  • This part is 'ONLY' required if your vehicle is equipped with 'Coil Suspension'.

Template

CAUTION
  • Make sure the template is printed to scale. Use a ruler to measure the scale bar on the template after it has been printed. The scale bar must be 100 mm long.
NOTE
  • A printer is required to complete this step.
  • Cut along the edge of the printed template as illustrated.
REMOVAL INSTRUCTIONS
3

Open the tailgate.

4

Disconnect the vehicle start-up battery.

For additional information, please refer to the official Workshop Manual. 12V System Disconnect and Connect (414-01A)

5

Remove parcel shelf.

6

Remove the loadspace floor trim.

7

Remove the loadspace treadplate but pulling it up from its x6 clips.

8

Release the lower edge of the loadspace trim panels on both sides of the vehicle.

  1. Remove the x4 clips (black arrows).
  2. Remove the x2 D-loop anchor point (white arrows).
9

Remove junction box access panel

10

Remove foam tool tray.

11

Remove the rear under tray.

  1. Remove x8 fixings and the x1 fastener.
12
WARNING
  • This step requires the assistance of another person.

Remove the rear bumper.

  • For additional information, please refer to the official Workshop Manual. Rear Bumper (501-19)
Fitting Instruction
1
WARNING
  • Make sure to wear suitable personal protective equipment.
CAUTION
  • Make sure the drill bit and the hole cutter do not come into contact with the air suspension compressor when cutting through the air suspension compressor tray. The drill bit must not go deeper than 5 mm into the tray.

Mark and cut a hole in the air suspension compressor tray for the bike carrier harness.

  1. Mark the hole position in the air suspension compressor tray.
  2. Cut the hole, for the bike carrier harness, in the air suspension compressor tray using a 32 mm diameter hole cutter.
  3. Remove any cutting waste from the air suspension compressor tray.
2

Remove and retain x6 fixings to remove the rear bumper valance from the rear bumper.

3
NOTE
  • Align the template with the edge of the bumper valance. Make sure the edge of the template matches the cutouts in the bumper valance as arrowed.

Locate and secure the template as illustrated.

4

Mark the x3 hole positions on the bumper valance. Use the template to identify where to mark the hole positions.

5
WARNING
  • Make sure to wear suitable personal protective equipment.

Drill and cut the holes in the bumper valance for the x2 fixings (C) and the bike carrier harness (A).

  1. Drill a 2 mm pilot hole at the location of the 2 fixing holes and the location of the bike carrier harness hole.
  2. Drill the x2 holes in the bumper valance for the fixings (C) using a 5mm diameter drill bit.
  3. Cut 1 hole in the bumper valance for the bike carrier harness using a 32mm diameter hole cutter.
  4. Discard the cut out sections.
  5. File the edges of the x3 holes.
6
NOTE
  • Applying lubricant to the grommet will help secure the grommet to the bumper valance.

Feed the section of the bike carrier harness (B1) that is attached to the bike carrier harness socket, through the hole in the bumper valance. The arrowed grommet for the air suspension tray must go through the hole.

  • Secure the bike carrier harness grommet to the bumper valance.
7

Install the bike carrier harness socket to the bumper valance using the x2 fixings (C) and x2 washers (D).

  • Torque: 2Nm
8
NOTE
  • Take care to align and feed the bike carrier harness through the rear bumper as illustrated.

Install the bumper valance, with the bike carrier harness, to the rear bumper with x6 fixings that were retained when it was removed.

9
WARNING
  • This step requires the assistance of another person.

Install the rear bumper.

  • For additional information, please refer to the official Workshop Manual. Rear Bumper (501-19)
10
NOTE
  • Make sure the bike carrier harness grommet fully seals around the hole.
  • Applying lubricant to the grommet will help secure the grommet to the air suspension compressor tray.

Install the bike carrier harness grommet to the air suspension compressor tray.

  • Continue feeding the bike carrier harness (B1) through the hole in the air suspension compressor tray as illustrated.
11
NOTE
  • This step is 'ONLY' required if your vehicle is equipped with 'Coil Suspension'.

Install bracket (U) with fixings (V) and (W).

  • Torque: 10Nm
12
NOTE
  • Coil Suspension variant shown. Air Suspension is similar.
  • TRM bracket is already installed if your vehicle has air suspension.

Install the (R) to bracket and secure using x2 M6 nuts (S).

  • Torque: 10Nm
13

Place the bike carrier harness (B2) into the loadspace.

14

Connect the bike carrier harness (B2) to the trailer light module (R).

  1. Connect the bike carrier harness to the trailer light module.
  2. Connect the clip into the vehicle stud as illustrated.
15
CAUTION
  • Take care not to damage the loadspace left trim panel.
NOTE
  • Loadspace side trim removed from parts of illustration to provide extra clarity.

Remove the blanking plug from the vehicles body harness connector.

  1. Carefully move aside the rear lower edge of the loadspace left trim panel.
  2. Release the clip and remove the blanking plug from the connector.
16
CAUTION
  • Take care not to damage the loadspace left trim panel.
NOTE
  • Loadspace side trim removed from illustration to provide extra clarity.

Connect the bike carrier harness (B2) to the vehicle body wiring harness as illustrated.

17

Route the bike carrier harness (B2) along the top of the vehicle body harness.

  1. Feed the bike carrier harness (B2) through the Noise, Vibration and Harshness (NVH) pad.
  2. Position the bike carrier harness (B2) over the top of the vehicle body harness.
18

Connect together the 2 parts of the bike carrier harness (B1) and (B2) as illustrated.

19
NOTE
  • NVH pads have been removed from illustration to provide extra clarity.
  • Route the bike carrier harness (B1) and (B2) along the top of the vehicle body harness where possible.

Secure the bike carrier harness (B1) and (B2) to the vehicle body wiring harness.

  1. Use the foam tape p around the connectors at the 2 locations as illustrated.
  2. Use the tie clips (H) at the 5 locations as illustrated. Make sure the bike carrier harness (B1) and (B2) is routed along the top of the vehicle body wiring harness where possible.
  3. Make sure the bike carrier harness (B2) has sufficient clearance from the treadplate fixing point.
20
CAUTION
  • Move the earth bolt cable so it has the same orientation as the vehicle body harness and avoids risk of getting trapped.

Attach the bike carrier harness (B2) to the ground point using the earth bolt as illustrated.

  • Torque: 10Nm
  • Move the earth bolt cable so it has the same orientation as the vehicle body harness and avoids risk of getting trapped.
21
NOTE
  • Loadspace side trim removed from illustration to provide extra clarity.
  • Route the bike carrier harness (B1) and (B2) along the top of the vehicle body harness where possible.

Secure the bike carrier harness (B1) and (B2) to the vehicle body wiring harness using the tie clips (H) at the 3 locations as illustrated.

  1. Feed the bike carrier harness (B2) through the NVH pad.
  2. Make sure the bike carrier harness parts (B1) and (B2) have sufficient clearance from the treadplate fixing point.
22

Diagnostic.

  1. Using the Jaguar Land Rover approved diagnostic equipment, update the Trailer Light Module to the latest software.
  2. Using the Jaguar Land Rover approved diagnostic equipment, configure the Trailer Light Module to enable bike carrier electrics on the vehicle.
23

Install the rear under tray.

  1. Install x8 fixings and the x1 fastener.
24

Install the foam tool tray.

25

Install junction box access panel

26

Secure loadspace side trim panel on both sides of the vehicle.

  1. Install the x4 clips (black arrows).
  2. Install the x2 D-loop anchor point (white arrows). Torque 24Nm
27

Install an clip into place the loadspace treadplate with its x6 clips.

28

Remove the loadspace floor trim.

29

Install parcel shelf.

30

Connect the vehicle start-up battery.

For additional information, please refer to the official Workshop Manual. 12V System Disconnect and Connect (414-01A)

31

Close the tailgate.